Arria® V Device Datasheet

Download PDF
ID 683022
Date 5/23/2023
Public
Document Table of Contents
Document Table of Contents x
1. Arria® V GX, GT, SX, and ST Device Datasheet 2. Arria V GZ Device Datasheet
1. Arria® V GX, GT, SX, and ST Device Datasheet x
1.1. Electrical Characteristics 1.2. Switching Characteristics 1.3. Configuration Specifications 1.4. I/O Timing 1.5. Glossary 1.6. Arria® V GX, GT, SX, and ST Device Datasheet Revision History
1.1. Electrical Characteristics x
1.1.1. Operating Conditions
1.1.1. Operating Conditions x
1.1.1.1. Absolute Maximum Ratings 1.1.1.2. Maximum Allowed Overshoot and Undershoot Voltage 1.1.1.3. Recommended Operating Conditions 1.1.1.4. DC Characteristics 1.1.1.5. I/O Standard Specifications
1.1.1.3. Recommended Operating Conditions x
1.1.1.3.1. Recommended Operating Conditions 1.1.1.3.2. Transceiver Power Supply Operating Conditions 1.1.1.3.3. HPS Power Supply Operating Conditions
1.1.1.4. DC Characteristics x
1.1.1.4.1. Supply Current and Power Consumption 1.1.1.4.2. I/O Pin Leakage Current 1.1.1.4.3. Bus Hold Specifications 1.1.1.4.4. OCT Calibration Accuracy Specifications 1.1.1.4.5. OCT Without Calibration Resistance Tolerance Specifications 1.1.1.4.6. OCT Variation after Power-Up Calibration 1.1.1.4.7. Pin Capacitance 1.1.1.4.8. Hot Socketing 1.1.1.4.9. Internal Weak Pull-Up Resistor
1.1.1.5. I/O Standard Specifications x
1.1.1.5.1. Single-Ended I/O Standards 1.1.1.5.2. Single-Ended SSTL, HSTL, and HSUL I/O Reference Voltage Specifications 1.1.1.5.3. Single-Ended SSTL, HSTL, and HSUL I/O Standards Signal Specifications 1.1.1.5.4. Differential SSTL I/O Standards 1.1.1.5.5. Differential HSTL and HSUL I/O Standards 1.1.1.5.6. Differential I/O Standard Specifications
1.2. Switching Characteristics x
1.2.1. Transceiver Performance Specifications 1.2.2. Core Performance Specifications 1.2.3. Periphery Performance 1.2.4. HPS Specifications
1.2.1. Transceiver Performance Specifications x
1.2.1.1. Transceiver Specifications for Arria V GX and SX Devices 1.2.1.2. Transceiver Specifications for Arria V GT and ST Devices 1.2.1.3. CTLE Response at Data Rates > 3.25 Gbps across Supported AC Gain and DC Gain 1.2.1.4. CTLE Response at Data Rates ≤ 3.25 Gbps across Supported AC Gain and DC Gain 1.2.1.5. Typical TX VOD Setting for Arria® V Transceiver Channels with termination of 100 Ω 1.2.1.6. Transmitter Pre-Emphasis Levels 1.2.1.7. Transceiver Compliance Specification
1.2.2. Core Performance Specifications x
1.2.2.1. Clock Tree Specifications 1.2.2.2. PLL Specifications 1.2.2.3. DSP Block Performance Specifications 1.2.2.4. Memory Block Performance Specifications 1.2.2.5. Internal Temperature Sensing Diode Specifications
1.2.3. Periphery Performance x
1.2.3.1. High-Speed I/O Specifications 1.2.3.2. DPA Lock Time Specifications 1.2.3.3. LVDS Soft-CDR/DPA Sinusoidal Jitter Tolerance Specifications 1.2.3.4. DLL Frequency Range Specifications 1.2.3.5. DQS Logic Block Specifications 1.2.3.6. Memory Output Clock Jitter Specifications 1.2.3.7. OCT Calibration Block Specifications 1.2.3.8. Duty Cycle Distortion (DCD) Specifications
1.2.4. HPS Specifications x
1.2.4.1. HPS Clock Performance 1.2.4.2. HPS PLL Specifications 1.2.4.3. Quad SPI Flash Timing Characteristics 1.2.4.4. SPI Timing Characteristics 1.2.4.5. SD/MMC Timing Characteristics 1.2.4.6. USB Timing Characteristics 1.2.4.7. Ethernet Media Access Controller (EMAC) Timing Characteristics 1.2.4.8. I2C Timing Characteristics 1.2.4.9. NAND Timing Characteristics 1.2.4.10. Arm* Trace Timing Characteristics 1.2.4.11. UART Interface 1.2.4.12. GPIO Interface 1.2.4.13. HPS JTAG Timing Specifications
1.2.4.2. HPS PLL Specifications x
1.2.4.2.1. HPS PLL VCO Frequency Range 1.2.4.2.2. HPS PLL Input Clock Range 1.2.4.2.3. HPS PLL Input Jitter
1.3. Configuration Specifications x
1.3.1. POR Specifications 1.3.2. FPGA JTAG Configuration Timing 1.3.3. FPP Configuration Timing 1.3.4. Active Serial (AS) Configuration Timing 1.3.5. DCLK Frequency Specification in the AS Configuration Scheme 1.3.6. Passive Serial (PS) Configuration Timing 1.3.7. Initialization 1.3.8. Configuration Files 1.3.9. Minimum Configuration Time Estimation 1.3.10. Remote System Upgrades 1.3.11. User Watchdog Internal Oscillator Frequency Specifications
1.3.3. FPP Configuration Timing x
1.3.3.1. DCLK-to-DATA[] Ratio (r) for FPP Configuration 1.3.3.2. FPP Configuration Timing when DCLK-to-DATA[] = 1 1.3.3.3. FPP Configuration Timing when DCLK-to-DATA[] >1
1.4. I/O Timing x
1.4.1. Programmable IOE Delay 1.4.2. Programmable Output Buffer Delay
2. Arria V GZ Device Datasheet x
2.1. Electrical Characteristics 2.2. Switching Characteristics 2.3. Configuration Specification 2.4. I/O Timing 2.5. Glossary 2.6. Arria® V GZ Device Datasheet Revision History
2.1. Electrical Characteristics x
2.1.1. Operating Conditions
2.1.1. Operating Conditions x
2.1.1.1. Absolute Maximum Ratings 2.1.1.2. Maximum Allowed Overshoot and Undershoot Voltage 2.1.1.3. Recommended Operating Conditions 2.1.1.4. DC Characteristics 2.1.1.5. I/O Standard Specifications
2.1.1.3. Recommended Operating Conditions x
2.1.1.3.1. Recommended Transceiver Power Supply Operating Conditions 2.1.1.3.2. Transceiver Power Supply Requirements
2.1.1.4. DC Characteristics x
2.1.1.4.1. Supply Current 2.1.1.4.2. Power Consumption 2.1.1.4.3. I/O Pin Leakage Current 2.1.1.4.4. Bus Hold Specifications 2.1.1.4.5. On-Chip Termination (OCT) Specifications 2.1.1.4.6. Pin Capacitance 2.1.1.4.7. Hot Socketing 2.1.1.4.8. Internal Weak Pull-Up Resistor
2.2. Switching Characteristics x
2.2.1. Transceiver Performance Specifications 2.2.2. Core Performance Specifications 2.2.3. Periphery Performance
2.2.1. Transceiver Performance Specifications x
2.2.1.1. Reference Clock 2.2.1.2. Transceiver Clocks 2.2.1.3. Receiver 2.2.1.4. Transmitter 2.2.1.5. CMU PLL 2.2.1.6. ATX PLL 2.2.1.7. Fractional PLL 2.2.1.8. Clock Network Data Rate 2.2.1.9. Standard PCS Data Rate 2.2.1.10. 10G PCS Data Rate 2.2.1.11. Typical VOD Settings
2.2.2. Core Performance Specifications x
2.2.2.1. Clock Tree Specifications 2.2.2.2. PLL Specifications 2.2.2.3. DSP Block Specifications 2.2.2.4. Memory Block Specifications 2.2.2.5. Temperature Sensing Diode Specifications
2.2.3. Periphery Performance x
2.2.3.1. High-Speed I/O Specification 2.2.3.2. DLL Range Specifications 2.2.3.3. DQS Logic Block Specifications 2.2.3.4. Memory Output Clock Jitter Specifications 2.2.3.5. OCT Calibration Block Specifications 2.2.3.6. Duty Cycle Distortion (DCD) Specifications
2.2.3.1. High-Speed I/O Specification x
2.2.3.1.1. High-Speed Clock Specifications 2.2.3.1.2. Transmitter High-Speed I/O Specifications 2.2.3.1.3. Receiver High-Speed I/O Specifications 2.2.3.1.4. DPA Mode High-Speed I/O Specifications 2.2.3.1.5. Soft CDR Mode High-Speed I/O Specifications 2.2.3.1.6. Non DPA Mode High-Speed I/O Specifications
2.3. Configuration Specification x
2.3.1. POR Specifications 2.3.2. JTAG Configuration Specifications 2.3.3. Fast Passive Parallel (FPP) Configuration Timing 2.3.4. Active Serial Configuration Timing 2.3.5. Passive Serial Configuration Timing 2.3.6. Initialization 2.3.7. Configuration Files 2.3.8. Remote System Upgrades Circuitry Timing Specification 2.3.9. User Watchdog Internal Oscillator Frequency Specification
2.3.3. Fast Passive Parallel (FPP) Configuration Timing x
2.3.3.1. DCLK-to-DATA[] Ratio (r) for FPP Configuration 2.3.3.2. FPP Configuration Timing when DCLK to DATA[] = 1 2.3.3.3. FPP Configuration Timing when DCLK to DATA[] > 1
2.4. I/O Timing x
2.4.1. Programmable IOE Delay 2.4.2. Programmable Output Buffer Delay
1. Arria® V GX, GT, SX, and ST Device Datasheet
2. Arria V GZ Device Datasheet

2.3.4. Active Serial Configuration Timing

Figure 31. AS Configuration TimingTiming waveform for the active serial (AS) x1 mode and AS x4 mode configuration timing.
Table 136.  AS Timing Parameters for AS x1 and AS x4 Configurations in Arria V GZ Devices

The minimum and maximum numbers apply only if you choose the internal oscillator as the clock source for initializing the device.

tCF2CD, tCF2ST0, tCFG, tSTATUS, and tCF2ST1 timing parameters are identical to the timing parameters for PS mode listed in the "PS Timing Parameters for Arria V GZ Devices" table.

Symbol Parameter Condition Minimum Maximum Unit
tCO 220 DCLK falling edge to AS_DATA0/ASDO output — — 4 ns
tSU 221 Data setup time before falling edge on DCLK — 1.5 — ns
tDH 221 Data hold time after falling edge on DCLK –3 speed grade 3.7 — ns
–4 speed grade 3.9 — ns
tCD2UM CONF_DONE high to user mode 222 — 175 437 μs
tCD2CU CONF_DONE high to CLKUSR enabled — 4 × maximum DCLK period — —
tCD2UMC CONF_DONE high to user mode with CLKUSR option on — tCD2CU + (8576 × CLKUSR period) — —
Table 137.  DCLK Frequency Specification in the AS Configuration Scheme

This applies to the DCLK frequency specification when using the internal oscillator as the configuration clock source.

The AS multi-device configuration scheme does not support DCLK frequency of 100 MHz.

Minimum Typical Maximum Unit
5.3 7.9 12.5 MHz
10.6 15.7 25.0 MHz
21.3 31.4 50.0 MHz
42.6 62.9 100.0 MHz
Related Information
220 Load capacitance for DCLK = 6 pF and AS_DATA/ASDO = 8 pF. Intel recommends obtaining the tCO for a given link (including receiver, transmission lines, connectors, and termination resistors) through IBIS or HSPICE simulation.
221 To evaluate the data setup (tSU) and data hold time (tDH) slack on your board in order to ensure you are meeting the tSU and tDH requirement, Intel recommends following the guideline in the "Evaluating Data Setup and Hold Timing Slack" chapter in AN822: Intel FPGA Configuration Device Migration Guideline.
222 To enable the CLKUSR pin as the initialization clock source and to obtain the maximum frequency specification on this pin, refer to the “Initialization” section of the Configuration, Design Security, and Remote System Upgrades in Arria V Devices chapter.
Level Two Title