Networking Interface for Open Programmable Acceleration Engine: Intel® Programmable Acceleration Card with Intel® Arria® 10 GX FPGA

Download PDF
ID 683532
Date 8/05/2019
Public
Document Table of Contents
Document Table of Contents x
1. Introduction 2. AFU Design 3. OPAE Support 4. Networking Interface for Open Programmable Acceleration Engine: Intel® PAC with Intel® Arria® 10 GX FPGA Revision History
1. Introduction x
1.1. How to Use this Guide
2. AFU Design x
2.1. HSSI Device Interface 2.2. Connecting the MAC to the HSSI PHY 2.3. Verifying Network Port Function
2.1. HSSI Device Interface x
2.1.1. HSSI Clocks 2.1.2. HSSI Unified Data Interface 2.1.3. HSSI PHY Control and Status 2.1.4. HSSI PR Management 2.1.5. HSSI Reset Control and Status 2.1.6. Initialization
2.2. Connecting the MAC to the HSSI PHY x
2.2.1. 4x10GBASE-SR Mode 2.2.2. 40GBASE-SR4 Mode
2.2.1. 4x10GBASE-SR Mode x
2.2.1.1. Clocks in 4x10GBASE-SR Mode 2.2.1.2. Unified Data Interface in 4x10GBASE-SR Mode 2.2.1.3. PHY Control and Status in 4x10GBASE-SR Mode 2.2.1.4. PR Management in 4x10GBASE-SR Mode 2.2.1.5. Reset Control and Status in 4x10GBASE-SR Mode 2.2.1.6. Initialization in 4x10GBASE-SR Mode 2.2.1.7. Unused 10GbE Channels
2.2.2. 40GBASE-SR4 Mode x
2.2.2.1. Clocks in 40GBASE-SR4 Mode 2.2.2.2. Unified Data Interface in 40GBASE-SR4 Mode 2.2.2.3. PHY Control and Status in 40GBASE-SR4 Mode 2.2.2.4. PR Management in 40GBASE-SR4 Mode 2.2.2.5. Reset Control and Status in 40GBASE-SR4 Mode 2.2.2.6. Initialization in 40GBASE-SR4 Mode
3. OPAE Support x
3.1. OPAE Driver HSSI sysfs Files 3.2. Managing the Network Port
3.1. OPAE Driver HSSI sysfs Files x
3.1.1. The board_id sysfs 3.1.2. The eeprom sysfs 3.1.3. The config sysfs 3.1.4. The equalizer_tune sysfs
3.1.4. The equalizer_tune sysfs x
3.1.4.1. Receiver CTLE AC Gain sysfs Encodings 3.1.4.2. Receiver VGA sysfs Encodings 3.1.4.3. Receiver CTLE DC Gain sysfs Encodings 3.1.4.4. Transmitter Pre-Emphasis First Post Tap Encodings 3.1.4.5. Transmitter Pre-Emphasis Second Post Tap Encodings 3.1.4.6. Transmitter Pre-Emphasis First Pre Tap Encodings 3.1.4.7. Transmitter Pre-Emphasis Second Pre Tap Encodings 3.1.4.8. Transmitter VOD Encodings
3.2. Managing the Network Port x
3.2.1. Configuring the Network Port 3.2.2. Reading the Base MAC Address from the Intel® PAC with Intel® Arria® 10 GX FPGA 3.2.3. Modifying HSSI PHY Transceiver PMA Settings
3.2.3. Modifying HSSI PHY Transceiver PMA Settings x
3.2.3.1. HSSI PHY Analog PMA Presets
1. Introduction
2. AFU Design
3. OPAE Support
4. Networking Interface for Open Programmable Acceleration Engine: Intel® PAC with Intel® Arria® 10 GX FPGA Revision History

2.2.1.2. Unified Data Interface in 4x10GBASE-SR Mode

Each 10GbE channel’s XGMII data interface is striped across 128-bit segments of the unified data interface transmit and receive data ports. The 64-bit XGMII data is mapped to the lower 64 bits of the 128-bit segment. The upper 64 bits of the transmit datapath segment should be statically driven low. The upper 64 bits of the receive datapath segment should be left unconnected.

Each 10GbE channel’s XGMII data control interface is striped across 18-bit segments of the unified data interface’s transmit and receive data control ports. The eight bits of control are mapped to the lower eight bits of the 18-bit segment. The control bit for the least significant XGMII data byte lane (e.g., xgmii_tx_data_out[7:0]) maps to the least significant bit of the unified data interface’s control port (e.g., a2f_tx_parallel_control[0] corresponds to xgmii_tx_control_out[0]) with each successive control bit mapping similarly to the same bit index of the unified data interface control port. The upper 10 bits of the transmit data control segment should be statically driven low. The upper 10 bits of the receive data control segment should be left unconnected.

The HSSI PHY FIFO flow control ports are not utilized in 4x10GBASE-SR mode. Statically drive the a2f_tx_enh_data_valid and a2f_rx_enh_fifo_rd_en ports high.

Level Two Title