LVDS SERDES Transmitter / Receiver IP Cores User Guide

Download PDF
ID 683062
Date 12/15/2017
Public
Document Table of Contents
Document Table of Contents x
1. LVDS SERDES Transmitter/Receiver IP Cores User Guide
1. LVDS SERDES Transmitter/Receiver IP Cores User Guide x
1.1. Features 1.2. Parameter Settings 1.3. Ports 1.4. Prototypes and Component Declarations 1.5. Functional Description 1.6. Simulating Intel® FPGA IP Cores 1.7. Generating ALTLVDS IP Core Using Clear Box Generator 1.8. LVDS SERDES Transmitter/Receiver IP Cores User Guide Archives 1.9. Document Revision History for LVDS SERDES Transmitter/Receiver IP Cores User Guide
1.1. Features x
1.1.1. Resource Utilization and Performance
1.2. Parameter Settings x
1.2.1. ALTLVDS_TX Parameter Settings 1.2.2. ALTLVDS_RX Parameter Settings 1.2.3. Command Line Interface Parameters
1.3. Ports x
1.3.1. ALTLVDS_TX Ports 1.3.2. ALTLVDS_RX Ports
1.4. Prototypes and Component Declarations x
1.4.1. Verilog HDL Prototype 1.4.2. VHDL Component Declaration 1.4.3. VHDL LIBRARY-USE Declaration
1.5. Functional Description x
1.5.1. Receiver Modes 1.5.2. DPA PLL Calibration 1.5.3. Initialization and Reset 1.5.4. Source-Synchronous Timing Analysis and Timing Constraints 1.5.5. Arria II GX, Arria® V, Arria® V GZ, Cyclone® V, and Stratix® V LVDS Package Skew Compensation Report Panel 1.5.6. ALTLVDS IP Core in External PLL Mode
1.5.1. Receiver Modes x
1.5.1.1. DPA Mode 1.5.1.2. Non-DPA Mode 1.5.1.3. Soft-CDR Mode
1.5.1.3. Soft-CDR Mode x
1.5.1.3.1. Clock Forwarding 1.5.1.3.2. Standard Mode 1.5.1.3.3. No Output Register Mode
1.5.2. DPA PLL Calibration x
1.5.2.1. DPA PLL Calibration in Stratix IV ES Devices 1.5.2.2. DPA PLL Calibration in Arria II and Stratix IV Devices and Later 1.5.2.3. Effects of DPA PLL Calibration
1.5.3. Initialization and Reset x
1.5.3.1. Initializing ALTLVDS_TX and ALTLVDS_RX 1.5.3.2. Resetting the DPA 1.5.3.3. Aligning the Word Boundaries 1.5.3.4. Recommended Initialization and Reset Flow
1.5.4. Source-Synchronous Timing Analysis and Timing Constraints x
1.5.4.1. Dedicated SERDES 1.5.4.2. SERDES in LEs 1.5.4.3. Receiver Skew Margin and Transmitter Channel-to-Channel Skew 1.5.4.4. Setting Timing Constraints Using the TimeQuest Timing Analyzer GUI 1.5.4.5. Setting Timing Constraints Manually in the Synopsys Design Constraint File
1.5.4.3. Receiver Skew Margin and Transmitter Channel-to-Channel Skew x
1.5.4.3.1. Obtaining the RSKM Report 1.5.4.3.2. Obtaining the TCCS Report
1.5.4.4. Setting Timing Constraints Using the TimeQuest Timing Analyzer GUI x
1.5.4.4.1. Constraining the Input Clock Signal
1.5.6. ALTLVDS IP Core in External PLL Mode x
1.5.6.1. PLL Clock Signals for LVDS Interface in External PLL Mode 1.5.6.2. External PLL Compensation Mode for ALTLVDS IP Core in External PLL Mode
1. LVDS SERDES Transmitter/Receiver IP Cores User Guide

1.5.3.3. Aligning the Word Boundaries

To align the word boundaries, it is useful to have control characters in the data stream so that your logic can have a known pattern to search for. You can compare the data received for each channel, compare to the control character you are looking for, then pulse the rx_channel_data_align port as required until you successfully receive the control character.

Note: Intel recommends setting the rx_cda_max[] port to the deserialization factor or higher, which allows enough depth in the bit slip circuit to roll through an entire word if required.

If you do not have control characters in the received data, you need a deterministic relationship between the reference clock and data to predict the word boundary using timing simulation or laboratory measurements. The only way to ensure a deterministic relationship on the default word position in the SERDES when the device powers up, or anytime the PLL is reset, is to have a reference clock equal to the data rate divided by the deserialization factor. For example, if the data rate is 800 Mbps, and the deserialization factor is 8, the PLL requires a 100-MHz reference clock. This is important because the PLL locks to the rising edge of the reference clock. If you have one rising edge on the reference clock per serial word received, the deserializer always starts at the same position. Using timing simulation, or lab measurements, monitor the parallel words received and determine how many pulses are required on the rx_channel_data_align port to set your word boundaries. You can create a simple state machine to apply the required number of pulses when you enter user mode, or anytime you reset the PLL and DPA blocks.

Level Two Title