Intel® Quartus® Prime Standard Edition User Guide: Timing Analyzer

Download PDF
ID 683068
Date 2/21/2024
Public
Document Table of Contents
Document Table of Contents x
1. Timing Analysis Introduction 2. Using the Intel® Quartus® Prime Timing Analyzer A. Intel® Quartus® Prime Standard Edition User Guides
1. Timing Analysis Introduction x
1.1. Timing Analysis Basic Concepts 1.2. Document Revision History
1.1. Timing Analysis Basic Concepts x
1.1.1. Timing Path and Clock Analysis 1.1.2. Clock Setup Analysis 1.1.3. Clock Hold Analysis 1.1.4. Recovery and Removal Analysis 1.1.5. Multicycle Path Analysis 1.1.6. Metastability Analysis 1.1.7. Timing Pessimism 1.1.8. Clock-As-Data Analysis 1.1.9. Multicorner Analysis
1.1.1. Timing Path and Clock Analysis x
1.1.1.1. The Timing Netlist 1.1.1.2. Timing Paths 1.1.1.3. Data and Clock Arrival Times 1.1.1.4. Launch and Latch Edges
1.1.5. Multicycle Path Analysis x
1.1.5.1. Multicycle Clock Hold 1.1.5.2. Multicycle Clock Setup
2. Using the Intel® Quartus® Prime Timing Analyzer x
2.1. Enhanced Timing Analysis for Intel® Arria® 10 Devices 2.2. Basic Timing Analysis Flow 2.3. Using Timing Constraints 2.4. Timing Analyzer Tcl Commands 2.5. Timing Analysis of Imported Compilation Results 2.6. Using the Intel® Quartus® Prime Timing Analyzer Document Revision History
2.2. Basic Timing Analysis Flow x
2.2.1. Step 1: Open a Project and Run the Fitter 2.2.2. Step 2: Specify Timing Constraints 2.2.3. Step 3: Specify General Timing Analyzer Settings 2.2.4. Step 4: Run Timing Analysis 2.2.5. Step 5: Analyze Timing Analysis Results
2.2.5. Step 5: Analyze Timing Analysis Results x
2.2.5.1. Timing Report Commands 2.2.5.2. Set Operating Conditions 2.2.5.3. Fmax Summary Report 2.2.5.4. Report Timing Command 2.2.5.5. Correlating Constraints to the Timing Report 2.2.5.6. Locating Timing Paths in Other Tools
2.3. Using Timing Constraints x
2.3.1. Recommended Initial SDC Constraints 2.3.2. SDC File Precedence 2.3.3. Iterative Constraint Modification 2.3.4. Creating Clocks and Clock Constraints 2.3.5. Creating I/O Constraints 2.3.6. Creating Delay and Skew Constraints 2.3.7. Creating Timing Exceptions 2.3.8. Example Circuit and SDC File
2.3.1. Recommended Initial SDC Constraints x
2.3.1.1. Create Clock (create_clock) 2.3.1.2. Derive PLL Clocks (derive_pll_clocks) 2.3.1.3. Derive Clock Uncertainty (derive_clock_uncertainty) 2.3.1.4. Set Clock Groups (set_clock_groups)
2.3.4. Creating Clocks and Clock Constraints x
2.3.4.1. Creating Base Clocks 2.3.4.2. Creating Virtual Clocks 2.3.4.3. Creating Generated Clocks (create_generated_clock) 2.3.4.4. Deriving PLL Clocks 2.3.4.5. Creating Clock Groups (set_clock_groups) 2.3.4.6. Accounting for Clock Effect Characteristics
2.3.4.1. Creating Base Clocks x
2.3.4.1.1. Automatic Clock Detection and Constraint Creation
2.3.4.2. Creating Virtual Clocks x
2.3.4.2.1. Specifying I/O Interface Uncertainty 2.3.4.2.2. I/O Interface Clock Uncertainty Example
2.3.4.3. Creating Generated Clocks (create_generated_clock) x
2.3.4.3.1. Clock Divider Example (-divide_by) 2.3.4.3.2. Clock Multiplexor Example
2.3.4.5. Creating Clock Groups (set_clock_groups) x
2.3.4.5.1. Exclusive Clock Groups (-exclusive) 2.3.4.5.2. Asynchronous Clock Groups (-asynchronous) 2.3.4.5.3. set_clock_groups Constraint Tips
2.3.4.6. Accounting for Clock Effect Characteristics x
2.3.4.6.1. Set Clock Latency (set_clock_latency) 2.3.4.6.2. Clock Uncertainty
2.3.5. Creating I/O Constraints x
2.3.5.1. Input Constraints (set_input_delay) 2.3.5.2. Output Constraints (set_output_delay)
2.3.6. Creating Delay and Skew Constraints x
2.3.6.1. Advanced I/O Timing and Board Trace Model Delay 2.3.6.2. Maximum Skew (set_max_skew) 2.3.6.3. Net Delay (set_net_delay) 2.3.6.4. Create Timing Netlist
2.3.7. Creating Timing Exceptions x
2.3.7.1. Timing Constraint Precedence 2.3.7.2. False Paths (set_false_path) 2.3.7.3. Minimum and Maximum Delays 2.3.7.4. Multicycle Paths 2.3.7.5. Multicycle Exception Examples 2.3.7.6. Delay Annotation
2.3.7.4. Multicycle Paths x
2.3.7.4.1. Common Multicycle Applications 2.3.7.4.2. Relaxing Setup with Multicycle (set_multicyle_path) 2.3.7.4.3. Accounting for a Phase Shift (-phase)
2.3.7.5. Multicycle Exception Examples x
2.3.7.5.1. Default Multicycle Analysis 2.3.7.5.2. End Multicycle Setup = 2 and End Multicycle Hold = 0 2.3.7.5.3. End Multicycle Setup = 2 and End Multicycle Hold = 1 2.3.7.5.4. Same Frequency Clocks with Destination Clock Offset 2.3.7.5.5. Destination Clock Frequency is a Multiple of the Source Clock Frequency 2.3.7.5.6. Destination Clock Frequency is a Multiple of the Source Clock Frequency with an Offset 2.3.7.5.7. Source Clock Frequency is a Multiple of the Destination Clock Frequency 2.3.7.5.8. Source Clock Frequency is a Multiple of the Destination Clock Frequency with an Offset
2.4. Timing Analyzer Tcl Commands x
2.4.1. The quartus_sta Executable 2.4.2. Collection Commands 2.4.3. Identifying the Intel® Quartus® Prime Software Executable from the SDC File
2.4.2. Collection Commands x
2.4.2.1. Wildcard Characters 2.4.2.2. Adding and Removing Collection Items 2.4.2.3. Query of Collections 2.4.2.4. Using the get_pins Command
1. Timing Analysis Introduction
2. Using the Intel® Quartus® Prime Timing Analyzer
A. Intel® Quartus® Prime Standard Edition User Guides

2.3.3. Iterative Constraint Modification

You can iteratively modify .sdc constraints and reanalyze the timing results to ensure that you have the optimum constraints for your design.

Use the following steps to iteratively modify constraints:

  1. Click Tools > Timing Analyzer.
  2. Generate the reports you want to analyze. Double-click Report All Summaries under Macros to generate setup, hold, recovery, and removal summaries, as well as minimum pulse width checks, and a list of all the clock you define. These summaries cover all paths you constrain in your design. Whenever modifying or correcting constraints, generate the Diagnostic reports to identify unconstrained parts of your design, or ignored constraints.
  3. Analyze the results in the reports. When you are modifying constraints, rerun the reports to find any unexpected results. For example, a cross-domain path might indicate that you forgot to cut a transfer by including a clock in a clock group.
  4. Create or edit the appropriate constraints in your .sdc file and save the file.
  5. Double-click Reset Design in the Tasks pane. This removes all constraints from your design. Removing all constraints from your design allows rereading the .sdc files, including your changes.
  6. Regenerate the reports you want to analyze.
  7. Reanalyze the results.
  8. Repeat steps 4-7 as necessary.

This method performs timing analysis using new constraints, without any change to logic placement. While the Fitter uses the original constraints for place and route, the Timing Analyzer applies the new constraints. If there is any failing timing against the new constraints, this indicates a need to run place-and-route again.

Related Information
Level Two Title